You have no items in your shopping cart.
F. Dick Honing Steels
For the last two hundred years, F. Dick steels have been widely recognized as the best made at world fairs and other competitions. Professional butchers likely have the best understanding of steels, or honing rods. Their work demands they start with a very sharp edge and they hone their knives every ten to fifteen minutes while working. Nearly all butchers use a polished or fine cut steel because they remove a minimum amount of metal from the edge of the knife. They will only realign the existing edge, which is what a steel is designed to do.
Our recommendation is to work with a very fine stone to rebuild your edge and a fine-cut F. Dick steel to keep it straight. When you are working as a carver / butcher, honing your knife four to six times an hour, for a full shift, you will probably want to use a Friedrich Dick polished steel in order to avoid wearing the edge down. Most cooks hone the knife before starting work or after taking it to the sharpening stone. For them, the F. Dick regular cut steel works well. If you keep the knife edge aligned, you won’t have to grind a new edge as often and the knife lasts longer.
-
F. Dick Dickoron Hygienic Combi 12-inch Round Steel
Processing plants that use intensive cleaning agents and methods need a steel that stands up to them, and the Dickoron Hygienic Combi is made for that environment. One 12-inch round rod both sharpens and straightens the edge.Two sides carry a regular cut and two carry an ultra-fine cut. The regular cut faces restore bite to a knife that has gone dull on bone and joints, and the ultra-fine faces then straighten and refine the edge. Working both cuts on one rod saves carrying two steels on the belt.The round rod suits curved boning knives well.The ultra-fine cut alone is the Dickoron Micro 12-inch Oval Super Fine Cut Steel, the steel serious professionals buy most from us. A regular cut rod with a non-slip handle is the F. Dick 12-inch round steel with non-slip handle. Carry it in the F. Dick Knife Scabbard with Belt at the line. Learn More$125.45 -
F. Dick 8-inch Coarse Cut Kitchen Steel
F. Dick markets this smaller steel as a household steel, and its coarse cut renews the edge on standard German and American blades. Poultry processors who work with 5- and 6-inch boning knives use it extensively, since a short rod is all those knives need.An 8-inch rod is also a good choice for a hunter’s field kit, being small, light and easier to pack than a 10- or 12-inch steel. The coarse cut removes a little more metal than a regular cut, so a few strokes bring back a dull field knife. Follow it with a finer steel when a smoother edge is wanted.It fits a tackle box too.For a smaller steel still, the F. Dick pocket steel fits a pocket or tackle box. A regular cut kitchen steel is the F. Dick 10-inch round regular cut steel. Pair it with the MasterGrip 3-piece field dressing kit for the field. Learn More$22.10 -
F. Dick 12-inch Oval Regular Cut Steel
An oval rod gives the knife a broader face to ride on, which makes a steady angle easier to hold, and this 12-inch F. Dick steel pairs that shape with a regular cut. It is F. Dick’s entry point into its sharpening steels, with the same rod quality and a simpler handle.Regular cut grooves straighten and align a beveled edge on most German and American knives and give the edge a little tooth for slicing vegetables. The 12-inch length lets a 10-inch chef’s knife or a long slicer travel the full rod in one stroke. For knives harder than 60 Rockwell, a harder surface such as the Dickoron Titan 12-inch oval steel is a better match.A round version is the F. Dick 10-inch round regular cut steel. With a metal finger guard, the F. Dick 12-inch oval regular cut butcher steel is the next step up, and the EuroCut 12-inch oval regular cut steel is another option. Learn More$49.40 -
F. Dick DarkNitro 12-inch Oval Sharpening Steel
DarkNitro knives are harder than most F. Dick knives, and F. Dick developed this steel to straighten and align their edges. It has a special surface for very high abrasion, which makes it suitable for hard knives in general.The oval rod gives the knife a large contact area, so honing is more effective. The handle sits comfortably and securely in the hand and matches the DarkNitro knives. For a hard Japanese knife or a DarkNitro chef’s knife, it keeps the edge working between sessions on the stones.Light, regular strokes suit a hard edge best, since pressing hard can chip it. A few passes before each cooking session keep a DarkNitro or Japanese knife cutting cleanly, and the stones need to come out less frequently.Pair it with the DarkNitro 8.25-inch chef’s knife or the DarkNitro 7-inch santoku. Another steel for hard knives is the Dickoron Titan 12-inch oval steel, which has a black acrylic handle. Learn More$222.95 -
F. Dick 10-inch Square Regular and Fine Cut Combination Steel
Meat processors and serious cooks who hone constantly can work two cuts from one rod with this 10-inch square F. Dick steel. Two faces carry a regular cut and two carry a fine cut.The regular cut faces straighten a rolled edge and restore bite on a knife that has been working on bone and joints. The fine cut faces then smooth the edge for clean portioning. Four working faces also spread the wear across more of the rod. Accurate portions depend on a knife that stays sharp through the shift, which is what this rod is for.One rod also saves space at the station.For a smoother finish, the F. Dick 10-inch square polished and fine cut steel swaps the regular cut for polished faces. A round rod with a single regular cut is the 10-inch round steel with non-slip handle. Our honing steel guide explains when to use each cut. Learn More$66.30 -
F. Dick FineCut 12-inch Round Steel with Non-Slip Handle
Repeated contact with a cutting board pushes a sharp edge to one side or the other, and this 12-inch round FineCut steel is made to bring it back into line. About eight strokes on each side are enough to hone a rolled edge back to sharp.The fine cut removes little metal, so the rod can be used whenever the edge needs it without wearing the knife down. F. Dick hardens the rod so the lines keep their depth with use. The round profile follows the curve of boning and breaking knives precisely, and the handle is sealed for use in processing plants.An oval version is the FineCut 12-inch oval steel, which gives a broader face. For knives that need more correction, the 12-inch round regular cut steel with non-slip handle is the coarser sibling. Serious professionals who want a finer finish choose the Dickoron Micro 12-inch Oval Super Fine Cut Steel. Learn More$57.85 -
F. Dick 12-inch Oval Regular Cut Steel with Non-Slip Handle
For traditional German and American knives, a regular cut on an oval rod is a strong match, and this 12-inch F. Dick steel adds a non-slip handle for working professionals. The wider face makes the angle easier to find than on a round steel.The oval profile spreads contact over more of the edge, so fewer strokes bring a knife back. The handle stays put in a wet or gloved hand during quick touch-ups at the cutting table. It is sealed to the rod for cleanliness, which suits industrial use as well as restaurant kitchens.The broad face also helps a cutter who is still learning to hold a consistent angle on a steel.A round version is the 12-inch round steel with non-slip handle. For a smoother edge on the same shape, the FineCut 12-inch oval steel has a blue handle. Our best-selling steel overall is the EuroCut 12-inch Round Regular Cut Steel. Learn More$58.50 -
F. Dick 14-inch Round Regular Cut Steel with Non-Slip Handle
Long curved blades such as scimitars and breaking knives need extra length to hone properly, and this 14-inch round F. Dick steel provides it with a secure, non-slip handle. Butchers who hone constantly to keep portions and yields consistent on pork and beef will find it a practical tool.The regular cut straightens edges dulled by bone and joints and restores bite for trimming fat. A sealed handle keeps the steel suitable for the cleanest cutting environments. At this length, the rod lets a 12-inch blade sweep its full edge without running off the tip.A longer rod also keeps the hand farther from the edge as the knife sweeps toward the tip.For knives under 10 inches, the 12-inch round steel with non-slip handle is easier to carry. A black-handled butcher version is the F. Dick 14-inch round butcher steel, and the Dickoron Classic 14-inch round steel adds a sapphire cut. Learn More$48.75 -
F. Dick 12-inch Round Regular Cut Steel with Non-Slip Handle
Everyday honing on a 12-inch rod lets most knives pass evenly from heel to tip, even long ones, and this round F. Dick steel adds a non-slip handle for a secure grip. It is a dependable steel for butchers, processors and line cooks.The grooves are cut deep and even so they keep working with age, and the handle is sealed to the rod for cleaning in demanding environments. A regular cut restores bite to knives that have started to slide on meat or vegetables. The round profile gives precise control along the curve of a boning or breaking knife.Hang it at the station between uses.A shorter rod is the 10-inch round steel with non-slip handle, and the 14-inch handles scimitars. With a black handle and metal finger guard, the F. Dick 12-inch round butcher steel is a comparable rod. For a smoother edge, step up to the FineCut 12-inch round steel. Learn More$42.25 -
F. Dick Dickoron Duo 10-inch Diamond and Ceramic Steel
When a knife needs more attention than routine honing, the Dickoron Duo can cut a fresh edge and refine it on one rod. F. Dick makes it for sharpening and honing hard grades of steel.Two sides are diamond rods carrying millions of diamond grains, which remove metal and sharpen. The other two sides are ceramic, which smooths and straightens the edge after the diamond. A knife that has lost its edge through heavy use can get a new bevel on the diamond side and a smoother finish on the ceramic, which can save a trip to the stones.It is a good tool for a knife roll.For routine honing of hard knives, the Dickoron Titan 12-inch oval steel is the everyday rod. A diamond-only rod with a non-slip handle is the F. Dick 10-inch oval diamond sharpening steel. Our honing steel guide explains when to sharpen and when to hone. Learn More$133.25
