F. Dick Sharpeners

F. Dick Sharpeners are expertly crafted tools designed to keep your knives in optimal cutting condition. These guided tools are designed to efficiently hone and sharpen kitchen knives without any knowledge or skill. These sharpeners are easy to use and will ensure your knives remain sharp and ready for any task.

Items 1 to 10 of 13 total

per page

Page:
  1. 1
  2. 2
  • F. Dick Rapid Steel Action Set with Base

    The Rapid Steel Action takes the technique out of honing. Instead of holding an angle on a steel, the cook draws the knife through a slot where spring-loaded rods meet the edge from both sides at once, so burrs come off and the edge is realigned in a few strokes.Because the angle is built in, the Action suits busy kitchens and meat rooms where many people share knives and not everyone has learned to use a steel. It works on all steel types. The set comes with a non-slip base plate with suction cups, so the sharpener stays put on a counter while one hand guides the knife.For meat processing, the Rapid Steel HyperDrill II takes reworked fine cut rods instead. Replacement rods for this unit are the Action Rapid Steel replacement rods. Cooks who prefer a traditional steel can start with the EuroCut 12-inch Round Regular Cut Steel. Learn More
  • F. Dick Master Steel Ultra-Fine HyperDrill Knife Sharpener

    This Master Steel carries ultra-fine HyperDrill rods that remove burrs and realign the edge without the technical knowledge that makes a honing steel hard for some cutters. It is designed to be used in place of a honing rod for regular edge maintenance.The optimum angle is built in, and both sides of the edge are burnished at the same time. Protection rods with a polishing effect guide the blade, so the edge is not damaged on its way through. The sharpener is fast and safe in the hand, and a holder is available to fix it at the cutting table.It is a practical tool for cutters who never learned to use a steel.The current HyperDrill version is the Master Steel HyperDrill II. A polished-rod version is the Master Steel Polish. The table mount is the Master Steel holder, and spring housings are sold as the left and right parts. Learn More
  • F. Dick Holder for Master Steel Sharpener

    Fixing a Master Steel to the workstation leaves both hands free to guide the knife, and this F. Dick holder does that. It fits the Master Steel Polish and the Master Steel HyperDrill.The holder screws onto the workplace without special tools. It sets the sharpener in one of three positions, facing straight out or angled to the left or right, so a cutter can choose the angle that suits the station and the hand they cut with. A hole at the handle end lets the sharpener be chained or locked to the table to keep it from walking off.Mounted at a comfortable height, it lets each cutter pass the knife through with the same motion every time.It fits the Master Steel Polish, the Master Steel HyperDrill II and the Master Steel ultra-fine HyperDrill. For a sharpener that mounts directly with its own holes, see the Magneto Steel HyperDrill. For other Master Steel parts, call us at 1-800-714-8226. Learn More
  • F. Dick Master Steel Polish Knife Sharpener

    The Master Steel Polish straightens and smooths an edge with polished rods, so it maintains a sharp knife without removing metal. It replaces a honing steel for regular edge maintenance and needs none of the technique a steel does.The angle is built in, and both sides of the edge are burnished at once as the knife passes through the slot. It suits boning specialists and processors who hone many times a shift and want the smoothest edge. Used by hand, it is quick to pick up at the cutting table; mounted in the holder, it frees both hands for the knife.Keep it at the station so a few passes fit between cuts.For a little material removal along with smoothing, the Master Steel HyperDrill takes fine cut rods. The table mount is the Master Steel holder, and fresh rods are the Master Steel Polish replacement rods. Learn More
  • F. Dick Silver Steel HyperDrill Knife Sharpener

    With no springs and no plastic, the Silver Steel HyperDrill is built for processing plants where hygiene is checked closely and nothing can break off into the meat. It hones and aligns edges that already have a bevel, keeping blades sharp for cutting and breaking down carcasses.Two pairs of replaceable HyperDrill rods make up the sharpening unit, and F. Dick says the extra pair raises efficiency by a third. The angled handles have a thumb rest on both sides for safe hand-held use. With nothing to trap residue, every part is easy to clean between shifts.Mount it at the station or chain it in place so it stays where the cutters need it.An extension for this unit is the Silver Steel HyperDrill extension. For a sprung sharpener with guiding magnets, compare the Magneto Steel HyperDrill, and for a smaller hand unit, the Master Steel HyperDrill II. Learn More
  • F. Dick Extension for Silver Steel HyperDrill

    This genuine F. Dick extension is made to fit the Silver Steel HyperDrill, the spring-free sharpener used in meat plants. It is an accessory for an existing unit rather than a sharpener on its own.The Silver Steel is built without springs or vulnerable parts, so it suits stations where hygiene is checked closely. Fitting parts made for it keeps the unit working as designed and avoids loose or mismatched pieces at the cutting table. If you are not sure the extension is the part your station needs, call us before ordering and we will check it against your setup.Have the sharpener model and the station layout at hand when you call, and we can confirm the fit quickly.The sharpener itself is the F. Dick Silver Steel HyperDrill. For Master Steel units, see the Master Steel holder. We can also order other Silver Steel parts; call 1-800-714-8226. Learn More
  • F. Dick SM-100 Belt Grinding and Polishing Machine

    The SM-100 combines a belt grinder for coarse work with a felt polishing wheel for finishing. It sharpens all types of hand knives and machine knives, and it can grind and polish the complete blade right up to the handle.The belt grinding arm is infinitely adjustable and can be set in any position. Its grinding surface has two areas, one with a backing for straight, V-shaped grinding and one without for convex grinding. After grinding, the polishing wheel and buffing compound remove the burr and leave a smooth, refined edge. The motor runs quietly with little vibration, and rubber feet keep the machine steady.It suits a butcher shop or a sharpening service that handles many knives a week.Replacement supplies are the SM-100 grinding belts, the SM-100 polishing wheel and the white polishing compound. For a smaller machine with a preset angle, see the F. Dick RS-150 Duo. Learn More
  • F. Dick HyperDrill II Replacement Rods, Set of 3

    Fresh rods bring a Master Steel HyperDrill II back to full performance once the original set has worn. This set of three ultra-fine replacement rods has the same fine cut texture as the rods that come with the sharpener.HyperDrill II rods remove a little metal while smoothing the edge, so over many thousands of passes they wear. Swapping them keeps every knife on the line honed the same way, without replacing the whole unit.Worn rods show themselves when the edge takes more passes to come back or feels rough after honing. Keeping a spare set on hand means the sharpener does not sit idle while new rods are ordered.These rods fit the Master Steel HyperDrill II. For the polished version, order the Master Steel Polish replacement rods, and for the Action Rapid Steel, the Action replacement rods. The table below lists the other Master Steel parts. Learn More
  • F. Dick Master Steel Polish Replacement Rods, Set of 3

    When a Master Steel Polish stops leaving the edge as smooth as it did, a fresh set of rods restores it. This set of three replacement polishing rods has the same texture as the rods installed at the factory.The polished rods straighten and smooth the edge without removing metal, and after long service their surface wears. Replacing them keeps the built-in angle exactly as designed. These are original F. Dick parts.Signs that the rods need replacing include an edge that takes more passes to straighten, or one that no longer feels smooth after honing. A spare set on the shelf keeps the sharpener in service at a busy cutting table while a new order is on its way. Fit all three rods at once so the sharpener works evenly.These rods fit the Master Steel Polish. For the HyperDrill II version, order the HyperDrill II replacement rods. The Master Steel holder mounts the sharpener to a table, and the parts table lists the rest. Learn More
  • F. Dick 120 Grit Grinding Belts for SM-100, 10-Pack

    These genuine F. Dick 120 grit belts fit the SM-100 sharpening machine, and a pack of ten keeps a shop grinding through many sessions. The 120 grit abrasive removes material efficiently to reshape and restore a worn edge.Grinding belts lose their bite as they wear, which makes the machine work harder and heats the blade. Changing to a fresh belt restores fast, even grinding on both the backed area for V-shaped edges and the unbacked area for convex edges. Original belts are sized exactly for the SM-100’s grinding arm.Change the belt when it starts to glaze or load with metal, or when grinding takes noticeably longer than it did. A fresh belt cuts cooler and faster, which protects the temper of the edge. Store spare belts flat in a dry place so they keep their shape.These belts fit the F. Dick SM-100. After grinding, finish the edge on the SM-100 polishing wheel with the white polishing compound. Learn More

Items 1 to 10 of 13 total

per page

Page:
  1. 1
  2. 2