F. Dick Honing Steels

For the last two hundred years, F. Dick steels have been widely recognized as the best made at world fairs and other competitions. Professional butchers likely have the best understanding of steels, or honing rods. Their work demands they start with a very sharp edge and they hone their knives every ten to fifteen minutes while working. Nearly all butchers use a polished or fine cut steel because they remove a minimum amount of metal from the edge of the knife. They will only realign the existing edge, which is what a steel is designed to do.

Our recommendation is to work with a very fine stone to rebuild your edge and a fine-cut F. Dick steel to keep it straight. When you are working as a carver / butcher, honing your knife four to six times an hour, for a full shift, you will probably want to use a Friedrich Dick polished steel in order to avoid wearing the edge down. Most cooks hone the knife before starting work or after taking it to the sharpening stone. For them, the F. Dick regular cut steel works well. If you keep the knife edge aligned, you won’t have to grind a new edge as often and the knife lasts longer.

Items 21 to 30 of 42 total

per page

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  • F. Dick 10-inch Oval Diamond Sharpening Steel with Non-Slip Handle

    When a regular steel no longer brings an edge back, a diamond rod will, without soaking a stone or learning to hold an angle on one. Diamond is the fastest-cutting rod there is. This F. Dick rod is 600 grit with a solid core, and that construction matters. Diamond pressed into a solid core lasts for years, while hollow rods with an epoxied coating can wear through in six months to a year of regular use.The oval profile puts more of the rod against the blade on each stroke, so it takes fewer strokes, and you can feel the bevel against the rod more clearly. Diamond also works on hard steels that a plain steel rod cannot touch. Its one drawback is a slightly rougher finish, so it is worth following with a few strokes on a ceramic rod such as the Idahone 12-inch Fine Ceramic Sharpening Rod, Black Wood Handle.
    Diamond or Steel?For daily upkeep on a knife that is still sharp, a cut steel such as the F. Dick 10-inch Round Fine Cut Sharpening Steel, Red Handle is gentler and removes less metal. Keep the diamond rod for edges that have gone dull. Our Honing Rod Guide covers when each one makes sense. Learn More
  • F. Dick 10-inch Round Regular Cut Steel with Non-Slip Handle

    A non-slip handle matters when the hands are wet or greasy, and this 10-inch round F. Dick steel pairs one with a regular cut for everyday honing. It suits meat cutters and cooks who hone throughout a shift.F. Dick cuts the grooves deep and even, so the rod hones consistently and keeps its bite with use. The handle is sealed to the rod, which keeps it suitable for processing plants and busy kitchens with strict cleaning routines. Ten inches fits a standard knife block and suits boning, utility and chef’s knives up to about 8 inches.Keep it within reach of the cutting board so a few strokes between tasks become part of the routine.For longer knives, the 12-inch and 14-inch versions add reach. An oval rod with the same handle is the 12-inch oval regular cut steel with non-slip handle. For a finer finish, see the FineCut 10-inch oval steel. Learn More
  • F. Dick Red Spirit 10-inch Round Regular Cut Steel

    With its red handle, this 10-inch round steel completes the Red Spirit knife series and keeps those knives honed with a standard cut. Knives need regular attention on a steel to stay truly sharp, and this rod makes that part of the routine.The round shape is symmetrical in the hand and guides the knife in a smooth, even stroke. The handle holds firm in a wet hand. Ten inches is long enough for the Red Spirit chef’s knife and the AJAX, and it suits the series’ paring and boning knives too.Keep it by the board so a few strokes before each task become a habit, and the Red Spirit edge will stay keen between sharpenings.Pair it with the Red Spirit 8.5-inch chef’s knife or the Red Spirit Pit Master BBQ set. For the 10-inch Hektor scimitar, a longer rod such as the F. Dick 12-inch round steel with non-slip handle gives more room. Learn More
  • F. Dick 2.75-inch Pocket Steel

    Anglers, hunters and campers can carry this F. Dick pocket steel for quick touch-ups away from the kitchen. The regular cut rod brings back the edge on a pocket knife or a fillet knife wherever it is needed.To store it, unscrew the rod and screw it back in reversed, inside the handle, which protects the cut and keeps it from snagging in a pocket or tackle box. The rod resists corrosion, so it can sit in a bag between trips without rusting. It is small enough to keep in a glove box as well.Before a trip, check that the rod is screwed in firmly so it cannot work loose in a pack.For a field kit with room for a longer rod, the F. Dick 8-inch coarse cut steel gives more length. At home, the F. Dick 10-inch round regular cut steel fits a knife block. A fishing knife to carry with it is the ErgoGrip 4-inch fishing knife. Learn More
  • F. Dick 12-inch Oval Regular Cut Butcher Steel

    An oval face makes it easier to find and hold the honing angle, and this 12-inch F. Dick butcher steel pairs that shape with a regular cut and a metal finger guard. It suits cooks who want a more forgiving rod than a round steel.The regular cut grooves leave the edge with a little bite, which helps when slicing tomatoes and other vegetables thinly, and the edge also cuts proteins well. A couple of strokes on each side are enough to bring back a knife that has started to slide. The guard adds balance, and the hang ring keeps the steel at hand.The oval shape is also easier to learn on.A round version is the 12-inch round butcher steel. For a lighter oval rod, the EuroCut 12-inch oval regular cut steel is another choice. A smoother finish comes from an oval fine cut such as the EuroCut 12-inch oval fine cut steel. Learn More
  • F. Dick 14-inch Round Regular Cut Butcher Steel

    Long knives need a long rod, and this 14-inch F. Dick butcher steel gives scimitars, breaking knives and doner slicers enough length to sweep the full edge. It is built for butchers and processors who work with blades over 10 inches.A metal finger guard adds weight to the handle end, which balances the long rod and protects the hand. The regular cut straightens edges dulled by bone and joints and leaves enough bite for clean trimming. The extra length makes it harder to fit in a knife roll, so it is best kept on a hook or in a scabbard at the cutting station.For knives under 10 inches, the 12-inch round butcher steel is easier to carry. The same length with a sapphire cut is the Dickoron Classic 14-inch round steel, and a non-slip handle version is the F. Dick 14-inch round steel with non-slip handle. Learn More
  • F. Dick 12-inch Round Regular Cut Butcher Steel

    Twelve inches is the length that lets most knives pass the rod from heel to tip in one stroke, and this round F. Dick butcher steel is a standard choice for that work. It suits butchers, line cooks and home cooks with a mix of knife lengths.A metal finger guard protects the hand and balances the rod, and the hang ring keeps it handy on a hook by the cutting table. F. Dick tapers the rod and cuts the grooves evenly, so a consistent angle is easy to repeat. The regular cut puts a working edge back on knives used for meat and vegetables.It is a sensible first steel for a cook who owns knives of several lengths.A shorter version is the 10-inch round butcher steel, and the 14-inch suits long scimitars. For an oval face, see the 12-inch oval butcher steel. The EuroCut 12-inch Round Regular Cut Steel is the same length without the metal finger guard. Learn More
  • F. Dick 10-inch Round Regular Cut Butcher Steel

    This 10-inch round steel sits in the middle of F. Dick’s range, with a metal finger guard and a hang ring that the entry-level steels lack. The regular cut keeps butcher, boning and kitchen knives aligned through a day of use.The finger guard protects the hand if the edge slips and adds weight at the handle, which makes the rod feel balanced in the hand. Ten inches suits boning and utility knives as well as chef’s knives up to 8 inches. A longer rod is easier for curved blades such as a scimitar or a breaking knife, which need room to sweep the full edge.For a home cook, the 10-inch length also slips into a standard knife block, and the ring lets it hang beside the stove.For longer knives, the 12-inch and 14-inch versions of this butcher steel add reach. A step up in hardness and finish is the Dickoron Classic 12-inch round sapphire cut steel. Learn More
  • F. Dick MultiCut 11-inch Flat Fine and Regular Cut Steel

    The MultiCut has a fine surface for restoring and honing an edge with light strokes, and the edges of its grooves have a grinding effect that takes the shoulder of the edge back when a blunt knife is steeled more firmly. One flat rod handles both upkeep and correction. It is the highest-rated steel we sell.The flat face makes a consistent angle easy to meet. Fine lines align a burred edge and clear away metal flakes for a smooth cut. Keep it out of sight in a busy kitchen, or every cook on the line will want to touch up a knife on it. The handle is balanced against the heavy rod and sealed for clean environments.An oval rod with fine and regular cut is the Dickoron Multiron 12-inch oval steel. A flat fine cut alone is the F. Dick 2000 11-inch flat steel, and the Balkan flat butcher steel has an all-metal handle. Learn More
  • F. Dick Dickoron Classic 12-inch Oval Sapphire Cut Steel

    In Germany, the Dickoron oval is one of the steels professionals prefer, and it gives an extremely sharp edge. This 12-inch Dickoron Classic combines the sapphire cut with an oval rod that makes the angle easy to hold.What separates the sapphire and fine cuts? Both are grooved to a similar depth, but the sapphire has straight, very fine striations running from handle to tip, while the fine cut runs in a wavy S pattern. The fine cut is therefore slightly more aggressive in texture than the sapphire. The oval face spreads the stroke across more of the edge for quick, even results.It suits sushi and fish work as well as butchery.A round version is the Dickoron Classic 12-inch round steel. For an ultra-fine finish, serious professionals choose the Dickoron Micro 12-inch Oval Super Fine Cut Steel. The S-pattern fine cut is available on the FineCut 12-inch oval steel. Learn More

Items 21 to 30 of 42 total

per page

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5