You have no items in your shopping cart.
F. Dick Honing Steels
For the last two hundred years, F. Dick steels have been widely recognized as the best made at world fairs and other competitions. Professional butchers likely have the best understanding of steels, or honing rods. Their work demands they start with a very sharp edge and they hone their knives every ten to fifteen minutes while working. Nearly all butchers use a polished or fine cut steel because they remove a minimum amount of metal from the edge of the knife. They will only realign the existing edge, which is what a steel is designed to do.
Our recommendation is to work with a very fine stone to rebuild your edge and a fine-cut F. Dick steel to keep it straight. When you are working as a carver / butcher, honing your knife four to six times an hour, for a full shift, you will probably want to use a Friedrich Dick polished steel in order to avoid wearing the edge down. Most cooks hone the knife before starting work or after taking it to the sharpening stone. For them, the F. Dick regular cut steel works well. If you keep the knife edge aligned, you won’t have to grind a new edge as often and the knife lasts longer.
-
F. Dick Dickoron Multiron 12-inch Oval Steel
The Multiron combines a fine cut and a regular cut in one oval rod. Under light pressure it hones smoothly, and with more pressure slight indentations along the rod increase the abrasion to straighten damaged or burred edges.We like this steel at Knife Merchant because you can feel any problem areas on the knife as it passes. A bad spot on the edge announces itself by touch, so the cook knows where to work, and regular use on this rod lets a knife go longer between sharpenings. The cuts are fine and even for a consistent result along the 12-inch length.For a flat rod with fine and regular cuts, the F. Dick MultiCut 11-inch flat steel takes a similar approach. A single fine cut is the EuroCut 12-inch oval fine cut steel, and a finer Dickoron finish is the Dickoron Micro 12-inch Oval Super Fine Cut Steel. Learn More$123.50 -
F. Dick EuroCut 12-inch Oval Regular Cut Steel
When cooks come to our store looking for a honing tool, the EuroCut 12-inch oval is the model Chef David recommends. It offers F. Dick’s regular cut on an oval rod at a working-kitchen build.The oval shape makes the honing angle more forgiving to find, and the wider face reaches the whole edge from heel to tip. Regular cut grooves straighten a rolled edge and restore bite on chef’s knives, slicers and boning knives. F. Dick tapers and balances the rod so each stroke feels the same along its length.It also fits a full-size knife roll.Our best-selling steel overall is the round version, the EuroCut 12-inch Round Regular Cut Steel. For a finer finish on meat and fish, the EuroCut 12-inch oval fine cut steel is the sibling. Cooks who want a heavier rod with a metal finger guard can compare the F. Dick 12-inch oval butcher steel. Learn More$37.70 -
F. Dick EuroCut 12-inch Oval Fine Cut Steel
Butchers, sushi chefs and meat processors want an edge that cuts flesh without tearing, and this 12-inch EuroCut oval steel with a fine cut gives it. The edge is finer than a regular cut leaves, so slices of meat and fish come away clean.An oval face spreads contact across a wider area of the edge, which makes it easier to keep the angle steady during quick touch-ups at the board. The fine grooves remove little metal, so the rod can be used throughout a shift without wearing the knife down. The length suits slicers and breaking knives as well as chef’s knives.A light touch is all it needs.For more bite on vegetables, the EuroCut 12-inch oval regular cut steel is the sibling. A round version of this cut is the EuroCut 12-inch round fine cut steel, and a fine cut oval with a non-slip handle is the FineCut 12-inch oval steel. Learn More$43.55 -
F. Dick 12-inch Oval Regular Cut Steel with Non-Slip Handle
For traditional German and American knives, a regular cut on an oval rod is a strong match, and this 12-inch F. Dick steel adds a non-slip handle for working professionals. The wider face makes the angle easier to find than on a round steel.The oval profile spreads contact over more of the edge, so fewer strokes bring a knife back. The handle stays put in a wet or gloved hand during quick touch-ups at the cutting table. It is sealed to the rod for cleanliness, which suits industrial use as well as restaurant kitchens.The broad face also helps a cutter who is still learning to hold a consistent angle on a steel.A round version is the 12-inch round steel with non-slip handle. For a smoother edge on the same shape, the FineCut 12-inch oval steel has a blue handle. Our best-selling steel overall is the EuroCut 12-inch Round Regular Cut Steel. Learn More$58.50 -
F. Dick DarkNitro 12-inch Oval Sharpening Steel
DarkNitro knives are harder than most F. Dick knives, and F. Dick developed this steel to straighten and align their edges. It has a special surface for very high abrasion, which makes it suitable for hard knives in general.The oval rod gives the knife a large contact area, so honing is more effective. The handle sits comfortably and securely in the hand and matches the DarkNitro knives. For a hard Japanese knife or a DarkNitro chef’s knife, it keeps the edge working between sessions on the stones.Light, regular strokes suit a hard edge best, since pressing hard can chip it. A few passes before each cooking session keep a DarkNitro or Japanese knife cutting cleanly, and the stones need to come out less frequently.Pair it with the DarkNitro 8.25-inch chef’s knife or the DarkNitro 7-inch santoku. Another steel for hard knives is the Dickoron Titan 12-inch oval steel, which has a black acrylic handle. Learn More$222.95 -
F. Dick 12-inch Oval Regular Cut Steel
An oval rod gives the knife a broader face to ride on, which makes a steady angle easier to hold, and this 12-inch F. Dick steel pairs that shape with a regular cut. It is F. Dick’s entry point into its sharpening steels, with the same rod quality and a simpler handle.Regular cut grooves straighten and align a beveled edge on most German and American knives and give the edge a little tooth for slicing vegetables. The 12-inch length lets a 10-inch chef’s knife or a long slicer travel the full rod in one stroke. For knives harder than 60 Rockwell, a harder surface such as the Dickoron Titan 12-inch oval steel is a better match.A round version is the F. Dick 10-inch round regular cut steel. With a metal finger guard, the F. Dick 12-inch oval regular cut butcher steel is the next step up, and the EuroCut 12-inch oval regular cut steel is another option. Learn More$49.40
