You have no items in your shopping cart.
F. Dick Honing Steels
For the last two hundred years, F. Dick steels have been widely recognized as the best made at world fairs and other competitions. Professional butchers likely have the best understanding of steels, or honing rods. Their work demands they start with a very sharp edge and they hone their knives every ten to fifteen minutes while working. Nearly all butchers use a polished or fine cut steel because they remove a minimum amount of metal from the edge of the knife. They will only realign the existing edge, which is what a steel is designed to do.
Our recommendation is to work with a very fine stone to rebuild your edge and a fine-cut F. Dick steel to keep it straight. When you are working as a carver / butcher, honing your knife four to six times an hour, for a full shift, you will probably want to use a Friedrich Dick polished steel in order to avoid wearing the edge down. Most cooks hone the knife before starting work or after taking it to the sharpening stone. For them, the F. Dick regular cut steel works well. If you keep the knife edge aligned, you won’t have to grind a new edge as often and the knife lasts longer.
-
F. Dick Dickoron Hygienic Combi 12-inch Round Steel
Processing plants that use intensive cleaning agents and methods need a steel that stands up to them, and the Dickoron Hygienic Combi is made for that environment. One 12-inch round rod both sharpens and straightens the edge.Two sides carry a regular cut and two carry an ultra-fine cut. The regular cut faces restore bite to a knife that has gone dull on bone and joints, and the ultra-fine faces then straighten and refine the edge. Working both cuts on one rod saves carrying two steels on the belt.The round rod suits curved boning knives well.The ultra-fine cut alone is the Dickoron Micro 12-inch Oval Super Fine Cut Steel, the steel serious professionals buy most from us. A regular cut rod with a non-slip handle is the F. Dick 12-inch round steel with non-slip handle. Carry it in the F. Dick Knife Scabbard with Belt at the line. Learn More$125.45 -
F. Dick 8-inch Coarse Cut Kitchen Steel
F. Dick markets this smaller steel as a household steel, and its coarse cut renews the edge on standard German and American blades. Poultry processors who work with 5- and 6-inch boning knives use it extensively, since a short rod is all those knives need.An 8-inch rod is also a good choice for a hunter’s field kit, being small, light and easier to pack than a 10- or 12-inch steel. The coarse cut removes a little more metal than a regular cut, so a few strokes bring back a dull field knife. Follow it with a finer steel when a smoother edge is wanted.It fits a tackle box too.For a smaller steel still, the F. Dick pocket steel fits a pocket or tackle box. A regular cut kitchen steel is the F. Dick 10-inch round regular cut steel. Pair it with the MasterGrip 3-piece field dressing kit for the field. Learn More$22.10 -
F. Dick FineCut 12-inch Round Steel with Non-Slip Handle
Repeated contact with a cutting board pushes a sharp edge to one side or the other, and this 12-inch round FineCut steel is made to bring it back into line. About eight strokes on each side are enough to hone a rolled edge back to sharp.The fine cut removes little metal, so the rod can be used whenever the edge needs it without wearing the knife down. F. Dick hardens the rod so the lines keep their depth with use. The round profile follows the curve of boning and breaking knives precisely, and the handle is sealed for use in processing plants.An oval version is the FineCut 12-inch oval steel, which gives a broader face. For knives that need more correction, the 12-inch round regular cut steel with non-slip handle is the coarser sibling. Serious professionals who want a finer finish choose the Dickoron Micro 12-inch Oval Super Fine Cut Steel. Learn More$57.85 -
F. Dick 14-inch Round Regular Cut Steel with Non-Slip Handle
Long curved blades such as scimitars and breaking knives need extra length to hone properly, and this 14-inch round F. Dick steel provides it with a secure, non-slip handle. Butchers who hone constantly to keep portions and yields consistent on pork and beef will find it a practical tool.The regular cut straightens edges dulled by bone and joints and restores bite for trimming fat. A sealed handle keeps the steel suitable for the cleanest cutting environments. At this length, the rod lets a 12-inch blade sweep its full edge without running off the tip.A longer rod also keeps the hand farther from the edge as the knife sweeps toward the tip.For knives under 10 inches, the 12-inch round steel with non-slip handle is easier to carry. A black-handled butcher version is the F. Dick 14-inch round butcher steel, and the Dickoron Classic 14-inch round steel adds a sapphire cut. Learn More$48.75 -
F. Dick 12-inch Round Regular Cut Steel with Non-Slip Handle
Everyday honing on a 12-inch rod lets most knives pass evenly from heel to tip, even long ones, and this round F. Dick steel adds a non-slip handle for a secure grip. It is a dependable steel for butchers, processors and line cooks.The grooves are cut deep and even so they keep working with age, and the handle is sealed to the rod for cleaning in demanding environments. A regular cut restores bite to knives that have started to slide on meat or vegetables. The round profile gives precise control along the curve of a boning or breaking knife.Hang it at the station between uses.A shorter rod is the 10-inch round steel with non-slip handle, and the 14-inch handles scimitars. With a black handle and metal finger guard, the F. Dick 12-inch round butcher steel is a comparable rod. For a smoother edge, step up to the FineCut 12-inch round steel. Learn More$42.25 -
F. Dick Dickoron Duo 10-inch Diamond and Ceramic Steel
When a knife needs more attention than routine honing, the Dickoron Duo can cut a fresh edge and refine it on one rod. F. Dick makes it for sharpening and honing hard grades of steel.Two sides are diamond rods carrying millions of diamond grains, which remove metal and sharpen. The other two sides are ceramic, which smooths and straightens the edge after the diamond. A knife that has lost its edge through heavy use can get a new bevel on the diamond side and a smoother finish on the ceramic, which can save a trip to the stones.It is a good tool for a knife roll.For routine honing of hard knives, the Dickoron Titan 12-inch oval steel is the everyday rod. A diamond-only rod with a non-slip handle is the F. Dick 10-inch oval diamond sharpening steel. Our honing steel guide explains when to sharpen and when to hone. Learn More$133.25 -
F. Dick EuroCut 12-inch Round Fine Cut Steel
The EuroCut fine cut has lighter lines than the regular cut, so it leaves a smoother, less roughened edge. That edge slices fish and beef cleanly without tearing, which makes this 12-inch round steel a good choice for portioning and carving.Fine cut steels remove less metal and mainly straighten a rolled edge, so they suit knives that are honed regularly and kept sharp. The round profile gives precise contact along curved blades such as boning knives and scimitars. Twelve inches lets a long slicer pass the rod in one stroke.It is a good second steel beside a regular cut.For more bite on vegetables, the round regular cut sibling is the EuroCut 12-inch Round Regular Cut Steel, our best-selling steel overall. An oval version of this rod is the EuroCut 12-inch oval fine cut steel. For a finer finish still, serious professionals choose the Dickoron Micro 12-inch Oval Super Fine Cut Steel. Learn More$27.95 -
F. Dick EuroCut 12-inch Round Regular Cut Steel
This is the best-selling steel in our shop. The EuroCut line puts the same F. Dick rod, with the same warranty, in a less expensive handle, so the money goes into the part that touches the knife. For American and German knives, it is the best value in a honing rod we carry.Regular cut has noticeably more texture than fine cut. That extra bite keeps a working edge on knives that see heavy daily use, and it helps on tough or waxy produce such as tomatoes and bell peppers, which a fine cut can struggle with. At 12 inches, the rod is long enough to hone a 10-inch chef’s knife or slicer in one full stroke. The round profile is the one compromise, since a round rod can roll off a counter where an oval one will not.
Regular or Fine Cut?For a gentler touch-up on knives that are already sharp, the F. Dick EuroCut 12-inch Round Fine Cut Steel has the same handle and length with less texture. If you would rather have more contact with the blade and a rod that stays put on the counter, choose the F. Dick EuroCut 12-inch Oval Regular Cut Steel. Our Honing Rod Guide explains how to match a rod to your knives. Learn More$26.65 -
F. Dick 10-inch Non-Chromium Polishing Steel
In meat packing plants this is simply called a butcher’s steel. It is stainless steel left unplated, because many cutters scuff the smooth surface with sandpaper until it has the texture they prefer. David leaves his smooth and uses it to burnish the edges on his protein knives.A smooth rod is the right match for stamped butcher knives from Victorinox and Dexter-Russell. Their steel runs soft, around 54 to 56 Rockwell, and comes back sharp on a polishing rod alone. On steel this soft, a textured rod is more than the edge needs. A smooth rod is also the standard for poultry and seafood processing, where the cleanest possible edge matters. Any tearing at the cellular level is the first thing to discolor on delicate proteins. A knife such as the Victorinox Fibrox Pro 5-inch Curved Semi-Stiff Boning Knife is exactly what this steel is for.
Smooth or Fine Cut?For harder German and American knives that need a little bite, choose the F. Dick 10-inch Round Fine Cut Sharpening Steel, Red Handle. The F. Dick Poliron 10-inch Polish Steel with Non-Slip Handle is another smooth steel, with a non-slip handle. Our Honing Rod Guide matches rod textures to steel hardness. Learn More$31.20 -
F. Dick 10-inch Round Regular Cut Steel with Non-Slip Handle
A non-slip handle matters when the hands are wet or greasy, and this 10-inch round F. Dick steel pairs one with a regular cut for everyday honing. It suits meat cutters and cooks who hone throughout a shift.F. Dick cuts the grooves deep and even, so the rod hones consistently and keeps its bite with use. The handle is sealed to the rod, which keeps it suitable for processing plants and busy kitchens with strict cleaning routines. Ten inches fits a standard knife block and suits boning, utility and chef’s knives up to about 8 inches.Keep it within reach of the cutting board so a few strokes between tasks become part of the routine.For longer knives, the 12-inch and 14-inch versions add reach. An oval rod with the same handle is the 12-inch oval regular cut steel with non-slip handle. For a finer finish, see the FineCut 10-inch oval steel. Learn More$38.35
