F. Dick Honing Steels

For the last two hundred years, F. Dick steels have been widely recognized as the best made at world fairs and other competitions. Professional butchers likely have the best understanding of steels, or honing rods. Their work demands they start with a very sharp edge and they hone their knives every ten to fifteen minutes while working. Nearly all butchers use a polished or fine cut steel because they remove a minimum amount of metal from the edge of the knife. They will only realign the existing edge, which is what a steel is designed to do.

Our recommendation is to work with a very fine stone to rebuild your edge and a fine-cut F. Dick steel to keep it straight. When you are working as a carver / butcher, honing your knife four to six times an hour, for a full shift, you will probably want to use a Friedrich Dick polished steel in order to avoid wearing the edge down. Most cooks hone the knife before starting work or after taking it to the sharpening stone. For them, the F. Dick regular cut steel works well. If you keep the knife edge aligned, you won’t have to grind a new edge as often and the knife lasts longer.

Items 1 to 10 of 15 total

per page

Page:
  1. 1
  2. 2
  • F. Dick 10-inch Square Regular and Fine Cut Combination Steel

    Meat processors and serious cooks who hone constantly can work two cuts from one rod with this 10-inch square F. Dick steel. Two faces carry a regular cut and two carry a fine cut.The regular cut faces straighten a rolled edge and restore bite on a knife that has been working on bone and joints. The fine cut faces then smooth the edge for clean portioning. Four working faces also spread the wear across more of the rod. Accurate portions depend on a knife that stays sharp through the shift, which is what this rod is for.One rod also saves space at the station.For a smoother finish, the F. Dick 10-inch square polished and fine cut steel swaps the regular cut for polished faces. A round rod with a single regular cut is the 10-inch round steel with non-slip handle. Our honing steel guide explains when to use each cut. Learn More
  • F. Dick Dickoron Duo 10-inch Diamond and Ceramic Steel

    When a knife needs more attention than routine honing, the Dickoron Duo can cut a fresh edge and refine it on one rod. F. Dick makes it for sharpening and honing hard grades of steel.Two sides are diamond rods carrying millions of diamond grains, which remove metal and sharpen. The other two sides are ceramic, which smooths and straightens the edge after the diamond. A knife that has lost its edge through heavy use can get a new bevel on the diamond side and a smoother finish on the ceramic, which can save a trip to the stones.It is a good tool for a knife roll.For routine honing of hard knives, the Dickoron Titan 12-inch oval steel is the everyday rod. A diamond-only rod with a non-slip handle is the F. Dick 10-inch oval diamond sharpening steel. Our honing steel guide explains when to sharpen and when to hone. Learn More
  • F. Dick 10-inch Non-Chromium Polishing Steel

    In meat packing plants this is simply called a butcher’s steel. It is stainless steel left unplated, because many cutters scuff the smooth surface with sandpaper until it has the texture they prefer. David leaves his smooth and uses it to burnish the edges on his protein knives.A smooth rod is the right match for stamped butcher knives from Victorinox and Dexter-Russell. Their steel runs soft, around 54 to 56 Rockwell, and comes back sharp on a polishing rod alone. On steel this soft, a textured rod is more than the edge needs. A smooth rod is also the standard for poultry and seafood processing, where the cleanest possible edge matters. Any tearing at the cellular level is the first thing to discolor on delicate proteins. A knife such as the Victorinox Fibrox Pro 5-inch Curved Semi-Stiff Boning Knife is exactly what this steel is for.
    Smooth or Fine Cut?For harder German and American knives that need a little bite, choose the F. Dick 10-inch Round Fine Cut Sharpening Steel, Red Handle. The F. Dick Poliron 10-inch Polish Steel with Non-Slip Handle is another smooth steel, with a non-slip handle. Our Honing Rod Guide matches rod textures to steel hardness. Learn More
  • F. Dick Poliron 10-inch Oval Polished Steel with Non-Slip Handle

    Butchers and meat processors who want the smoothest edge a honing rod can give reach for a polished steel such as the Poliron. A smooth edge cuts meat without tearing, which helps keep portions even and yields high.A polished surface removes no metal. It straightens the edge and polishes it, so it can follow a coarser steel to refine an edge that a regular or fine cut has roughened. Slim edges tend to fold over before they actually go dull, and a few strokes on the Poliron set them upright again. The oval face makes the angle easy to hold.To pair it with a coarser rod, the 10-inch round regular cut steel with non-slip handle shares the handle style. A square rod with polished and fine faces is the F. Dick 10-inch square polished and fine cut steel, and a Dickoron polished rod is the Dickoron Polish 12-inch oval steel. Learn More
  • F. Dick FineCut 10-inch Oval Steel with Non-Slip Handle

    Rather than straight grooves, the FineCut pattern resembles a series of S shapes. It removes a burr and smooths the edge without leaving micro-serrations, and it works well on German knives and on Japanese knives too.A 10-inch rod is short enough to carry in a scabbard and long enough for most kitchen knives, including chef’s knives and breaking knives up to 10 inches. The oval face gives more contact than a round rod, so the edge comes back in fewer strokes. Because it is a fine cut, it maintains an edge rather than repairing a damaged one.It also suits a scabbard on the belt.A 12-inch version is the FineCut 12-inch oval steel. When the edge needs more correction, a regular cut such as the 10-inch round steel with non-slip handle takes it further. A red-handled round fine cut is the F. Dick 10-inch round fine cut steel. Learn More
  • F. Dick 10-inch Square Polished and Fine Cut Combination Steel

    Four faces give this 10-inch F. Dick combination steel two finishes in one rod, with two polished sides and two fine cut sides. Butchers and meat processors who need to work efficiently can choose the edge for the job without reaching for a second steel.A polished edge is very smooth and suits cutting proteins into even portions. The fine cut sides leave a slightly rougher edge with a little bite, which helps when slicing tomatoes and other fruit and vegetables. The flat faces of the square rod also make it easy to see and hold the angle.It also suits a crowded knife roll.For more correction, the F. Dick 10-inch square regular and fine cut steel pairs a regular cut with a fine cut. A Dickoron version with sapphire and polished faces is the Dickoron Combi 12-inch square steel. A single polished rod is the Poliron 10-inch oval steel. Learn More
  • F. Dick 10-inch Oval Diamond Sharpening Steel with Non-Slip Handle

    When a regular steel no longer brings an edge back, a diamond rod will, without soaking a stone or learning to hold an angle on one. Diamond is the fastest-cutting rod there is. This F. Dick rod is 600 grit with a solid core, and that construction matters. Diamond pressed into a solid core lasts for years, while hollow rods with an epoxied coating can wear through in six months to a year of regular use.The oval profile puts more of the rod against the blade on each stroke, so it takes fewer strokes, and you can feel the bevel against the rod more clearly. Diamond also works on hard steels that a plain steel rod cannot touch. Its one drawback is a slightly rougher finish, so it is worth following with a few strokes on a ceramic rod such as the Idahone 12-inch Fine Ceramic Sharpening Rod, Black Wood Handle.
    Diamond or Steel?For daily upkeep on a knife that is still sharp, a cut steel such as the F. Dick 10-inch Round Fine Cut Sharpening Steel, Red Handle is gentler and removes less metal. Keep the diamond rod for edges that have gone dull. Our Honing Rod Guide covers when each one makes sense. Learn More
  • F. Dick 10-inch Round Regular Cut Steel with Non-Slip Handle

    A non-slip handle matters when the hands are wet or greasy, and this 10-inch round F. Dick steel pairs one with a regular cut for everyday honing. It suits meat cutters and cooks who hone throughout a shift.F. Dick cuts the grooves deep and even, so the rod hones consistently and keeps its bite with use. The handle is sealed to the rod, which keeps it suitable for processing plants and busy kitchens with strict cleaning routines. Ten inches fits a standard knife block and suits boning, utility and chef’s knives up to about 8 inches.Keep it within reach of the cutting board so a few strokes between tasks become part of the routine.For longer knives, the 12-inch and 14-inch versions add reach. An oval rod with the same handle is the 12-inch oval regular cut steel with non-slip handle. For a finer finish, see the FineCut 10-inch oval steel. Learn More
  • F. Dick Red Spirit 10-inch Round Regular Cut Steel

    With its red handle, this 10-inch round steel completes the Red Spirit knife series and keeps those knives honed with a standard cut. Knives need regular attention on a steel to stay truly sharp, and this rod makes that part of the routine.The round shape is symmetrical in the hand and guides the knife in a smooth, even stroke. The handle holds firm in a wet hand. Ten inches is long enough for the Red Spirit chef’s knife and the AJAX, and it suits the series’ paring and boning knives too.Keep it by the board so a few strokes before each task become a habit, and the Red Spirit edge will stay keen between sharpenings.Pair it with the Red Spirit 8.5-inch chef’s knife or the Red Spirit Pit Master BBQ set. For the 10-inch Hektor scimitar, a longer rod such as the F. Dick 12-inch round steel with non-slip handle gives more room. Learn More
  • F. Dick 10-inch Round Regular Cut Butcher Steel

    This 10-inch round steel sits in the middle of F. Dick’s range, with a metal finger guard and a hang ring that the entry-level steels lack. The regular cut keeps butcher, boning and kitchen knives aligned through a day of use.The finger guard protects the hand if the edge slips and adds weight at the handle, which makes the rod feel balanced in the hand. Ten inches suits boning and utility knives as well as chef’s knives up to 8 inches. A longer rod is easier for curved blades such as a scimitar or a breaking knife, which need room to sweep the full edge.For a home cook, the 10-inch length also slips into a standard knife block, and the ring lets it hang beside the stove.For longer knives, the 12-inch and 14-inch versions of this butcher steel add reach. A step up in hardness and finish is the Dickoron Classic 12-inch round sapphire cut steel. Learn More

Items 1 to 10 of 15 total

per page

Page:
  1. 1
  2. 2