F. Dick Honing Steels

For the last two hundred years, F. Dick steels have been widely recognized as the best made at world fairs and other competitions. Professional butchers likely have the best understanding of steels, or honing rods. Their work demands they start with a very sharp edge and they hone their knives every ten to fifteen minutes while working. Nearly all butchers use a polished or fine cut steel because they remove a minimum amount of metal from the edge of the knife. They will only realign the existing edge, which is what a steel is designed to do.

Our recommendation is to work with a very fine stone to rebuild your edge and a fine-cut F. Dick steel to keep it straight. When you are working as a carver / butcher, honing your knife four to six times an hour, for a full shift, you will probably want to use a Friedrich Dick polished steel in order to avoid wearing the edge down. Most cooks hone the knife before starting work or after taking it to the sharpening stone. For them, the F. Dick regular cut steel works well. If you keep the knife edge aligned, you won’t have to grind a new edge as often and the knife lasts longer.

6 Item(s)

per page

  • F. Dick Dickoron Combi 12-inch Square Sapphire and Polished Steel

    Two finishes on one rod give serious meat processors, butchers and fishmongers a choice of edge for the day’s work. On this 12-inch square Dickoron Combi, two opposite faces carry the sapphire cut and the other two are polished.The sapphire faces straighten the edge and give fine honing, leaving a slightly toothier edge that suits slicing fruit and vegetables. The polished faces then finish the blade after sharpening for an extremely smooth, sharp edge that portions proteins cleanly. The square profile makes each face distinct, so it is easy to tell which finish is in use.It replaces two rods at a crowded station.A single polished rod is the Dickoron Polish 12-inch oval steel, and the sapphire cut alone comes on the Dickoron Classic 12-inch oval steel. A smaller combination rod with a non-slip handle is the F. Dick 10-inch square polished and fine cut steel. Learn More
  • F. Dick MultiCut 11-inch Flat Fine and Regular Cut Steel

    The MultiCut has a fine surface for restoring and honing an edge with light strokes, and the edges of its grooves have a grinding effect that takes the shoulder of the edge back when a blunt knife is steeled more firmly. One flat rod handles both upkeep and correction. It is the highest-rated steel we sell.The flat face makes a consistent angle easy to meet. Fine lines align a burred edge and clear away metal flakes for a smooth cut. Keep it out of sight in a busy kitchen, or every cook on the line will want to touch up a knife on it. The handle is balanced against the heavy rod and sealed for clean environments.An oval rod with fine and regular cut is the Dickoron Multiron 12-inch oval steel. A flat fine cut alone is the F. Dick 2000 11-inch flat steel, and the Balkan flat butcher steel has an all-metal handle. Learn More
  • F. Dick 10-inch Square Polished and Fine Cut Combination Steel

    Four faces give this 10-inch F. Dick combination steel two finishes in one rod, with two polished sides and two fine cut sides. Butchers and meat processors who need to work efficiently can choose the edge for the job without reaching for a second steel.A polished edge is very smooth and suits cutting proteins into even portions. The fine cut sides leave a slightly rougher edge with a little bite, which helps when slicing tomatoes and other fruit and vegetables. The flat faces of the square rod also make it easy to see and hold the angle.It also suits a crowded knife roll.For more correction, the F. Dick 10-inch square regular and fine cut steel pairs a regular cut with a fine cut. A Dickoron version with sapphire and polished faces is the Dickoron Combi 12-inch square steel. A single polished rod is the Poliron 10-inch oval steel. Learn More
  • F. Dick Dickoron Multiron 12-inch Oval Steel

    The Multiron combines a fine cut and a regular cut in one oval rod. Under light pressure it hones smoothly, and with more pressure slight indentations along the rod increase the abrasion to straighten damaged or burred edges.We like this steel at Knife Merchant because you can feel any problem areas on the knife as it passes. A bad spot on the edge announces itself by touch, so the cook knows where to work, and regular use on this rod lets a knife go longer between sharpenings. The cuts are fine and even for a consistent result along the 12-inch length.For a flat rod with fine and regular cuts, the F. Dick MultiCut 11-inch flat steel takes a similar approach. A single fine cut is the EuroCut 12-inch oval fine cut steel, and a finer Dickoron finish is the Dickoron Micro 12-inch Oval Super Fine Cut Steel. Learn More
  • F. Dick 10-inch Square Regular and Fine Cut Combination Steel

    Meat processors and serious cooks who hone constantly can work two cuts from one rod with this 10-inch square F. Dick steel. Two faces carry a regular cut and two carry a fine cut.The regular cut faces straighten a rolled edge and restore bite on a knife that has been working on bone and joints. The fine cut faces then smooth the edge for clean portioning. Four working faces also spread the wear across more of the rod. Accurate portions depend on a knife that stays sharp through the shift, which is what this rod is for.One rod also saves space at the station.For a smoother finish, the F. Dick 10-inch square polished and fine cut steel swaps the regular cut for polished faces. A round rod with a single regular cut is the 10-inch round steel with non-slip handle. Our honing steel guide explains when to use each cut. Learn More
  • F. Dick Dickoron Hygienic Combi 12-inch Round Steel

    Processing plants that use intensive cleaning agents and methods need a steel that stands up to them, and the Dickoron Hygienic Combi is made for that environment. One 12-inch round rod both sharpens and straightens the edge.Two sides carry a regular cut and two carry an ultra-fine cut. The regular cut faces restore bite to a knife that has gone dull on bone and joints, and the ultra-fine faces then straighten and refine the edge. Working both cuts on one rod saves carrying two steels on the belt.The round rod suits curved boning knives well.The ultra-fine cut alone is the Dickoron Micro 12-inch Oval Super Fine Cut Steel, the steel serious professionals buy most from us. A regular cut rod with a non-slip handle is the F. Dick 12-inch round steel with non-slip handle. Carry it in the F. Dick Knife Scabbard with Belt at the line. Learn More

6 Item(s)

per page