You have no items in your shopping cart.
F. Dick Honing Steels
For the last two hundred years, F. Dick steels have been widely recognized as the best made at world fairs and other competitions. Professional butchers likely have the best understanding of steels, or honing rods. Their work demands they start with a very sharp edge and they hone their knives every ten to fifteen minutes while working. Nearly all butchers use a polished or fine cut steel because they remove a minimum amount of metal from the edge of the knife. They will only realign the existing edge, which is what a steel is designed to do.
Our recommendation is to work with a very fine stone to rebuild your edge and a fine-cut F. Dick steel to keep it straight. When you are working as a carver / butcher, honing your knife four to six times an hour, for a full shift, you will probably want to use a Friedrich Dick polished steel in order to avoid wearing the edge down. Most cooks hone the knife before starting work or after taking it to the sharpening stone. For them, the F. Dick regular cut steel works well. If you keep the knife edge aligned, you won’t have to grind a new edge as often and the knife lasts longer.
-
F. Dick Dickoron Combi 12-inch Square Sapphire and Polished Steel
Two finishes on one rod give serious meat processors, butchers and fishmongers a choice of edge for the day’s work. On this 12-inch square Dickoron Combi, two opposite faces carry the sapphire cut and the other two are polished.The sapphire faces straighten the edge and give fine honing, leaving a slightly toothier edge that suits slicing fruit and vegetables. The polished faces then finish the blade after sharpening for an extremely smooth, sharp edge that portions proteins cleanly. The square profile makes each face distinct, so it is easy to tell which finish is in use.It replaces two rods at a crowded station.A single polished rod is the Dickoron Polish 12-inch oval steel, and the sapphire cut alone comes on the Dickoron Classic 12-inch oval steel. A smaller combination rod with a non-slip handle is the F. Dick 10-inch square polished and fine cut steel. Learn More$141.05 -
F. Dick Dickoron Classic 14-inch Round Sapphire Cut Steel
Butchers, meat processors and cooks who carve shawarma and gyro with long slicers need a long rod, and this 14-inch Dickoron Classic adds the sapphire cut to that length. It is also well suited to curved scimitars and breaking knives.The extra length lets a 12-inch blade sweep its whole edge in one stroke, so the angle stays consistent from heel to tip. The fine, straight sapphire striations give velvety-soft honing and leave a uniform, fine edge. F. Dick cuts the lines with modern production methods so they run even and at the correct depth.Hang it at the station between cuts.For knives up to 10 inches, the Dickoron Classic 12-inch round steel is easier to carry. A regular cut at this length is the F. Dick 14-inch round butcher steel. A scabbard such as the F. Dick Knife Scabbard with Belt carries the steel with the knives. Learn More$109.20 -
F. Dick Dickoron Classic 12-inch Round Sapphire Cut Steel
The sapphire cut is used only in the Dickoron family, and this 12-inch round Dickoron Classic brings it to butchers, fishmongers and meat processors who want sharper knives and better yields. F. Dick describes the result as velvety-soft honing.The sapphire cut has straight, very fine striations running from handle to tip. It produces a uniformly sharp, fine edge that can be kept sharp for a long time before the knife needs regrinding. The round profile gives precise control along curved boning and breaking knives, and the substantial handle balances the rod well.It also fits a full-size knife roll.An oval version is the Dickoron Classic 12-inch oval steel, and the 14-inch round suits long scimitars. For a still finer cut, serious professionals choose the Dickoron Micro 12-inch Oval Super Fine Cut Steel. A lighter round steel at the same length is the EuroCut 12-inch Round Regular Cut Steel. Learn More$104.00 -
F. Dick Honorary 12-inch Oval Sapphire Cut Steel
The Honorary steel is the top of F. Dick’s range, a 12-inch oval rod with a handle that can be engraved. It makes a presentation piece for a retiring butcher, a culinary graduate or a chef marking a milestone.The rod carries the same fine sapphire cut as the Dickoron steels, so it hones gently and leaves a fine, even edge. It is extra hardened for less wear, and with the right care it can last a lifetime. The balance between the wood handle and the oval rod makes it comfortable for the long, steady strokes of daily honing.It is a steel to hand down to the next generation.The same sapphire cut with a plastic handle is the Dickoron Classic 12-inch oval steel. For a wood-handled steel to match a knife set, see the F. Dick DarkNitro steel with its oak handle or the F. Dick 1905 10-inch steel. Learn More$136.50 -
F. Dick Dickoron Polish 12-inch Oval Polished Steel
For extreme sharpness on knives with a very slim edge angle, F. Dick makes the Dickoron Polish. Its highly polished surface straightens the edge and polishes it without wearing the knife, which suits repetitive use through a long day.Meat processors, butchers and sushi chefs choose a polished steel over a coarser one when they want the smoothest possible edge. The Polish can follow a coarser steel to refine an edge the fine cut has roughened. The substantial Dickoron handle balances the 12-inch oval rod.A few light strokes before each service keep a thin edge standing upright, and the knife needs the stones less frequently.For a little more correction, the Dickoron Micro 12-inch Oval Super Fine Cut Steel adds an ultra-fine cut. A square rod with both sapphire and polished faces is the Dickoron Combi 12-inch square steel. A smaller polished rod with a non-slip handle is the Poliron 10-inch oval steel. Learn More$108.55 -
F. Dick Dickoron Micro 12-inch Oval Super Fine Cut Steel
Among serious professionals, this is the F. Dick steel we sell most. If your work is breaking down whole carcasses or cutting steak portions all day, you want the finest edge a steel can give, and the Dickoron Micro’s super fine cut delivers it. F. Dick cuts the lines evenly and to the right depth, and the rod’s hard surface wears very slowly.The oval profile makes honing more forgiving, because the flatter face gives the blade a steady surface to ride on and more contact per stroke. The handle is sealed to meat industry hygiene standards, so it holds up to the cleaning a processing room demands.
Other Dickoron SteelsThe F. Dick Dickoron 12-inch Oval Polishing Steel is the smooth version for the softest knives and the final polish. For an everyday steel at a lower cost, our best-selling steel overall is the F. Dick EuroCut 12-inch Round Regular Cut Steel. Learn More$112.45 -
F. Dick 2000 11-inch Flat Fine Cut Steel
A flat steel touches the edge along a line rather than at a single point, so it straightens and smooths the edge faster and more gently than a round rod. The Dick 2000 is an 11-inch flat steel with a fine cut.Alternating strokes bend the edge back and forth less on a flat face than on a round one, which is easier on a thin edge. The broad face also helps a cook hold the angle. Its grooves are cut deep to last, so the steel keeps its effect through years of daily use in a butcher shop or kitchen.An all-metal flat rod is the Balkan 10-inch flat butcher steel. For a flat rod that combines fine and regular cuts, see the F. Dick MultiCut 11-inch flat steel. An oval rod is another way to get a wide contact face, as on the EuroCut 12-inch oval fine cut steel. Learn More$134.55 -
F. Dick Balkan 10-inch Flat Fine Cut Butcher Steel
A flat steel makes cleaner contact between edge and rod than a round one, and this Balkan butcher steel puts that to work for meat cutters. Laying the edge against a flat face makes the angle easier to repeat, which makes honing more foolproof.The rod is fully forged with a one-piece, all-metal handle, and its rings act as a bolster to protect the hand. With no seam to trap residue, it suits industrial processing where hygiene is checked closely. The fine cut straightens and smooths the edge with little metal removed, so it can be used throughout a shift.It also sits comfortably in a scabbard worn on the belt.For a longer flat rod, the F. Dick 2000 11-inch flat steel has a plastic handle. The F. Dick MultiCut 11-inch flat steel adds a regular cut for heavier correction. Our honing steel guide explains flat and round rods. Learn More$87.10 -
F. Dick Dickoron Titan 12-inch Oval Coated Steel
Harder knives need a harder steel, and the Dickoron Titan is made for them. Its ultra-hard special coating is three times harder than standard sharpening steels, so it can work knives above 60 Rockwell that a standard rod would barely touch.The coating is slightly more abrasive than other steels, which helps it bring back an edge on hard Japanese knives and Damascus blades evenly. Meat processors also use it for the edge it gives for cutting through beef. For a fine finish, F. Dick recommends following it with the Dickoron Classic, and the oval face keeps the angle steady.For a cook with a mixed roll of German and Japanese knives, it handles the hardest blades in the set.Pair it with the Dickoron Classic 12-inch oval steel for that finishing step. Another rod for hard steels is the F. Dick DarkNitro 12-inch oval steel. A diamond option is the Dickoron Duo diamond and ceramic steel. Learn More$133.25 -
F. Dick 10-inch Round Regular Cut Steel
A 10-inch round steel is the right size for a home knife block, and this regular cut F. Dick rod keeps the edge on chef’s knives, slicers and paring knives aligned between sharpenings. It suits kitchens with mostly German and American knives.The regular cut has pronounced grooves, so a few strokes straighten a rolled edge and restore some bite to a knife that has started to slip on tomato skins. The round profile touches the edge at a single point, which gives precise control along a curved blade. Ten inches covers knives up to an 8-inch chef’s knife with room to spare.For a longer blade, the F. Dick 12-inch round butcher steel adds reach. An oval rod with a wider face is the F. Dick 12-inch oval regular cut steel. To finish with a smoother edge, step up to a fine cut such as the EuroCut 12-inch round fine cut steel. Learn More$35.75
