Steel Sharpening Rods

Maintain peak performance and extend the life of your kitchen knives with our high‑quality steel sharpening rods. Essential for honing blades between full stone sharpenings, these rods keep edges aligned and knives performing at their best. We carry a large variety of premium rods in specialized cuts, shapes, and lengths to suit every knife and steel type. Durable and easy to use, they are perfect for home cooks and professional chefs alike, helping you achieve smooth, precise cuts every time.

Items 11 to 20 of 25 total

per page

Page:
  1. 1
  2. 2
  3. 3
  • F. Dick 10-inch Round Regular Cut Steel with Non-Slip Handle

    A non-slip handle matters when the hands are wet or greasy, and this 10-inch round F. Dick steel pairs one with a regular cut for everyday honing. It suits meat cutters and cooks who hone throughout a shift.F. Dick cuts the grooves deep and even, so the rod hones consistently and keeps its bite with use. The handle is sealed to the rod, which keeps it suitable for processing plants and busy kitchens with strict cleaning routines. Ten inches fits a standard knife block and suits boning, utility and chef’s knives up to about 8 inches.Keep it within reach of the cutting board so a few strokes between tasks become part of the routine.For longer knives, the 12-inch and 14-inch versions add reach. An oval rod with the same handle is the 12-inch oval regular cut steel with non-slip handle. For a finer finish, see the FineCut 10-inch oval steel. Learn More
  • F. Dick EuroCut 12-inch Round Regular Cut Steel

    This is the best-selling steel in our shop. The EuroCut line puts the same F. Dick rod, with the same warranty, in a less expensive handle, so the money goes into the part that touches the knife. For American and German knives, it is the best value in a honing rod we carry.Regular cut has noticeably more texture than fine cut. That extra bite keeps a working edge on knives that see heavy daily use, and it helps on tough or waxy produce such as tomatoes and bell peppers, which a fine cut can struggle with. At 12 inches, the rod is long enough to hone a 10-inch chef’s knife or slicer in one full stroke. The round profile is the one compromise, since a round rod can roll off a counter where an oval one will not.
    Regular or Fine Cut?For a gentler touch-up on knives that are already sharp, the F. Dick EuroCut 12-inch Round Fine Cut Steel has the same handle and length with less texture. If you would rather have more contact with the blade and a rod that stays put on the counter, choose the F. Dick EuroCut 12-inch Oval Regular Cut Steel. Our Honing Rod Guide explains how to match a rod to your knives. Learn More
  • F. Dick EuroCut 12-inch Oval Regular Cut Steel

    When cooks come to our store looking for a honing tool, the EuroCut 12-inch oval is the model Chef David recommends. It offers F. Dick’s regular cut on an oval rod at a working-kitchen build.The oval shape makes the honing angle more forgiving to find, and the wider face reaches the whole edge from heel to tip. Regular cut grooves straighten a rolled edge and restore bite on chef’s knives, slicers and boning knives. F. Dick tapers and balances the rod so each stroke feels the same along its length.It also fits a full-size knife roll.Our best-selling steel overall is the round version, the EuroCut 12-inch Round Regular Cut Steel. For a finer finish on meat and fish, the EuroCut 12-inch oval fine cut steel is the sibling. Cooks who want a heavier rod with a metal finger guard can compare the F. Dick 12-inch oval butcher steel. Learn More
  • Victorinox 10-inch Regular Cut Honing Steel

    The Victorinox 10-inch regular cut steel is commonly mistaken for a knife sharpener. A honing steel maintains a knife’s edge and improves its cutting ability by pushing the rolled edge back into line, so the knife keeps cutting cleanly between sharpenings.We recommend a honing steel or rod about 2 inches longer than your longest knife for easier use. A 10-inch steel suits kitchens whose longest blade is an 8-inch chef’s knife, such as the Fibrox Pro 8-inch Chef’s Knife, and it fits a standard knife block.A regular cut has fine lengthwise grooves that realign the edge with a few light strokes. Use it before each prep session, and sharpen on a stone when honing no longer brings the edge back.For a finer surface, see the Victorinox 12-inch Fine Cut Honing Steel. The Victorinox 12-inch Regular Cut Honing Steel is the longer version. Our Honing Rod Guide explains honing in detail. Learn More
  • Victorinox 12-inch Regular Cut Honing Steel, Black Handle

    Over hundreds of cuts, the very edge of a knife rolls to one side and the knife stops biting into food. The Victorinox 12-inch regular cut honing steel realigns that edge with a few light strokes, restoring cutting performance without removing metal the way a sharpener does.The 12-inch rod is long enough for 10-inch chef’s knives and slicers and for butchery knives such as the Fibrox Pro 10-inch Scimitar, so the whole edge passes along the steel in one stroke.Hone before each work session, with the tip of the steel resting on a towel. Light, even strokes on alternate sides do more than heavy ones.Steel this length also hangs well on a hook at the station, where it is in reach for a few strokes between tasks.For a finer surface at this length, see the Victorinox 12-inch Fine Cut Honing Steel. The Victorinox 12-inch Combination Steel adds a polishing face. Our Honing Rod Guide explains each cut. Learn More
  • Victorinox 14-inch Regular Cut Honing Steel

    The Victorinox 14-inch regular cut steel maintains a knife’s sharp edge when it is used regularly. A honing steel does not sharpen knives; it realigns the edge of the blade so it cuts cleanly again.The 14-inch length suits the longest knives in a meat room, such as a 12-inch scimitar or the Fibrox Pro 14-inch Slicer, where a shorter steel cannot cover the whole edge in one stroke.It is made in England. Wash it by hand and dry it before storing.Keep it on a hook at the cutting table, where it is in reach between primals. A long steel also suits a shared station, since every knife on the table fits it.Hold the steel upright with the tip on a towel and draw the knife down and toward you, alternating sides. For a finer surface at this length, see the Victorinox 14-inch Fine Cut Honing Steel. Our Honing Rod Guide compares the cuts. Learn More
  • Victorinox 7-inch Regular Cut Honing Steel

    The Victorinox 7-inch regular cut steel is built for poultry processors and is ideal for boning knives and other small knives. The compact rod fits in a belt holder or a tackle box, so the edge can be touched up on the line or in the field.Poultry and game work dulls a boning knife quickly, and a few strokes on this steel between birds keep it cutting cleanly. It suits knives up to about 5 inches, such as the Fibrox Pro 5-inch Curved Semi-Stiff Boning Knife.Hold the steel in the free hand, set the heel of the knife at the top and draw it down the rod, alternating sides. Keep the strokes light and short.Wipe it clean between birds and dry it at the end of the shift.For longer knives, see the Victorinox 10-inch Regular Cut Honing Steel. Our Honing Rod Guide explains honing in detail. Learn More
  • Wüsthof 10-inch Deluxe Honing Steel

    Wüsthof’s 10-inch deluxe honing steel is a full-length steel for keeping the knives in your block in line. We recommend a steel at least 1 inch longer than your longest knife, so this 10-inch steel suits knives up to 9 inches, and it fits any Wüsthof block. Regular honing pushes the edge of a blade back to center after it bends slightly in use, and the knife feels sharp again without removing steel.Before you start cooking, give each side of the blade a few light passes down the rod. The longer rod gives a full sweep for long blades, and the handle is heavy enough to hold steady in one hand. German and American steel knives need regular honing to perform their best. This steel is designed to pair with Wüsthof knives, and it can be used on knives of any brand.Honing is maintenance; once a few strokes stop bringing the edge back, it is time to sharpen. The Wüsthof 10-inch ceramic sharpening rod removes a small amount of metal for knives that have gone dull, and the two-stage hand-held sharpener resets a worn edge. For a lighter steel, see the 10-inch honing steel with loop, and read our Honing Rod Guide for the steps. Learn More
  • Victorinox 10-inch Regular Cut Honing Steel, Dark Wood Handle

    Unlike a sharpening stone, which removes metal to create a new edge, this Victorinox regular cut steel realigns the existing edge of a knife after it rolls over in use. The 10-inch rod gives room for long strokes on knives from a paring knife up to an 8-inch chef’s knife.The dark wood handle has a guard between the hand and the rod and gives a classic look in a knife block or on a hook. The steel is made in the United Kingdom.Hone before each use with light strokes on alternate sides. The regular cut works well on Victorinox knives such as the Hardwood 8-inch Chef’s Knife, whose steel responds quickly to honing.Steel this length also hangs well on a hook at the station, where it is in reach for a few strokes between tasks.For more length with the same handle, see the Victorinox 12-inch Fine Cut Honing Steel. Our Honing Rod Guide explains each cut. Learn More
  • F. Dick 12-inch Round Regular Cut Steel with Non-Slip Handle

    Everyday honing on a 12-inch rod lets most knives pass evenly from heel to tip, even long ones, and this round F. Dick steel adds a non-slip handle for a secure grip. It is a dependable steel for butchers, processors and line cooks.The grooves are cut deep and even so they keep working with age, and the handle is sealed to the rod for cleaning in demanding environments. A regular cut restores bite to knives that have started to slide on meat or vegetables. The round profile gives precise control along the curve of a boning or breaking knife.Hang it at the station between uses.A shorter rod is the 10-inch round steel with non-slip handle, and the 14-inch handles scimitars. With a black handle and metal finger guard, the F. Dick 12-inch round butcher steel is a comparable rod. For a smoother edge, step up to the FineCut 12-inch round steel. Learn More

Items 11 to 20 of 25 total

per page

Page:
  1. 1
  2. 2
  3. 3