Steel Sharpening Rods

Maintain peak performance and extend the life of your kitchen knives with our high‑quality steel sharpening rods. Essential for honing blades between full stone sharpenings, these rods keep edges aligned and knives performing at their best. We carry a large variety of premium rods in specialized cuts, shapes, and lengths to suit every knife and steel type. Durable and easy to use, they are perfect for home cooks and professional chefs alike, helping you achieve smooth, precise cuts every time.

Items 51 to 60 of 72 total

per page

Page:
  1. 4
  2. 5
  3. 6
  4. 7
  5. 8
  • Wüsthof 10-inch Deluxe Honing Steel

    Wüsthof’s 10-inch deluxe honing steel is a full-length steel for keeping the knives in your block in line. We recommend a steel at least 1 inch longer than your longest knife, so this 10-inch steel suits knives up to 9 inches, and it fits any Wüsthof block. Regular honing pushes the edge of a blade back to center after it bends slightly in use, and the knife feels sharp again without removing steel.Before you start cooking, give each side of the blade a few light passes down the rod. The longer rod gives a full sweep for long blades, and the handle is heavy enough to hold steady in one hand. German and American steel knives need regular honing to perform their best. This steel is designed to pair with Wüsthof knives, and it can be used on knives of any brand.Honing is maintenance; once a few strokes stop bringing the edge back, it is time to sharpen. The Wüsthof 10-inch ceramic sharpening rod removes a small amount of metal for knives that have gone dull, and the two-stage hand-held sharpener resets a worn edge. For a lighter steel, see the 10-inch honing steel with loop, and read our Honing Rod Guide for the steps. Learn More
  • Zwilling Bob Kramer Double-Cut Sharpening Steel

    Zwilling has discontinued production of all Bob Kramer products. This was a highly rated honing rod by America’s Test Kitchen, but we offer similar, if not better, substitute rods that combine fine-cut and smooth surfaces.See the Friedr. Dick combination rods, the F. Dick 10-inch square combination steel and the F. Dick Dickoron 12-inch round combination steel, and the Victorinox combination rods, the Victorinox 10-inch combination steel and the Victorinox 12-inch combination steel. Learn More
  • Shun 9-inch Combination Honing Steel, Steel-Grey Handle

    Shun’s 9-inch combination honing steel keeps knife edges aligned with two surfaces in one rod, a smooth side for regular honing and a micro-ribbed side for more thorough realignment. A built-in angle guide sets the blade at 16°, so even a cook new to honing holds the correct angle.Its steel-grey handle suits any Shun series, which makes it the honing steel to choose for a mixed collection of Shun knives.
    Classic Handle OptionThe Shun Classic Combination Honing Steel has an ebony Pakkawood handle. Learn More
  • Granton 10 in. Packing House Steel

    Often referred to as a butcher's steel or packing house steel, the Granton® 10-Inch Magnetized Polishing Steel is the industry standard for professionals who rely on a perfect edge, shift after shift. Forged in Sheffield, England, this is not a simple honing rod; it is a precision finishing tool designed for the high-demand environments of meat processing, where safety, hygiene, and efficiency are paramount.  The Professional's Choice: The Packing House Standard Meat packers and professional butchers choose this specific type of steel for several critical reasons:  Essential Food Safety: In a commercial facility, hygiene is non-negotiable. As a knife is steeled, it sheds microscopic metal particles. The powerful magnetization of the Granton® steel instantly captures these filings, preventing them from contaminating meat or becoming airborne. Peak Efficiency and Reduced Fatigue: A polished edge glides through meat with significantly less friction than a merely honed edge. For a worker making thousands of cuts per day, this reduction in effort leads to faster work, cleaner cuts, and less physical fatigue. Superior, Longer-Lasting Edge: The super-fine polishing surface removes the microscopic "burr" left after sharpening, burnishing the steel to a flawlessly smooth, razor-keen edge that stays sharp longer under continuous use. Learn More
  • Granton 10-Inch Multi-Cut Combination Steel

    The Granton® 10-Inch Multi-Cut Combination Steel is a highly efficient tool for complete blade maintenance, designed for the professional or serious home cook who desires versatility and precision. Forged in Sheffield, England, this single steel effectively combines two distinct surfaces, providing the right tool for any situation—from daily edge alignment to final polishing. Fine-Cut Surfaces: These sides are the workhorse of the steel. They are designed for regular, daily honing to quickly realign a blade's edge that has begun to feel dull or has slightly rolled from use. They effectively restore a sharp cutting feel for continued work. Super-Fine (Polishing) Surfaces: After using the fine-cut side, or for blades that are already in good condition, a few strokes on the super-fine surfaces provide the ultimate refinement. These sides polish the edge, removing the most microscopic imperfections and creating an exceptionally keen, smooth finish that glides through food with minimal resistance. Learn More
  • Granton 12-Inch Multi-Cut Combination Steel

    Why Choose a 12-Inch Steel? The Professional Standard A professional rule of thumb states that a sharpening steel should be at least as long, and ideally two inches longer, than the blade of your longest knife. This makes the 12-inch Granton steel the essential choice for anyone using longer butcher knives, scimitars (typically 10-12 inches), and slicing knives. This extended length is crucial for safety and effectiveness. It allows you to draw the entire blade from heel to tip in one smooth, continuous motion, guaranteeing an evenly honed edge while keeping your guiding hand safely away from the blade. Two Steels in One: The Multi-Cut Advantage The Model 62102 rod features two opposing sides with a fine cut and two opposing sides with a super-fine (polishing) cut, delivering a complete two-stage maintenance system. 1) Fine-Cut Surfaces: These are the workhorse sides, designed for daily honing to quickly realign a blade's edge that has started to dull or roll. 2) Super-Fine (Polishing) Surfaces: After honing, a few strokes on the super-fine surfaces provide the ultimate refinement, polishing the edge to an exceptionally keen, smooth finish. Learn More
  • Victorinox 10-inch Regular Cut Honing Steel, Dark Wood Handle

    Unlike a sharpening stone, which removes metal to create a new edge, this Victorinox regular cut steel realigns the existing edge of a knife after it rolls over in use. The 10-inch rod gives room for long strokes on knives from a paring knife up to an 8-inch chef’s knife.The dark wood handle has a guard between the hand and the rod and gives a classic look in a knife block or on a hook. The steel is made in the United Kingdom.Hone before each use with light strokes on alternate sides. The regular cut works well on Victorinox knives such as the Hardwood 8-inch Chef’s Knife, whose steel responds quickly to honing.Steel this length also hangs well on a hook at the station, where it is in reach for a few strokes between tasks.For more length with the same handle, see the Victorinox 12-inch Fine Cut Honing Steel. Our Honing Rod Guide explains each cut. Learn More
  • Victorinox 12-inch Fine Cut Honing Steel, Dark Wood Handle

    A fine cut steel realigns an edge with less abrasion than a regular cut, which suits knives that are already sharp and need only a touch-up. This Victorinox 12-inch fine cut steel maintains a knife’s edge and improves its cutting ability, with a dark wood handle.The 12-inch rod gives full coverage for chef’s knives, slicers and butchery knives up to 10 inches. Breaking knives such as the Fibrox Pro 10-inch Granton Edge Breaking Knife respond well to a fine cut, which keeps the edge keen through long sessions.Use a few light strokes on alternate sides before each session. If the knife still drags, a regular cut or a sharpening stone is the next step.For the same handle in a shorter regular cut, see the Victorinox 10-inch Regular Cut Honing Steel. The Victorinox 14-inch Fine Cut Honing Steel is the long fine cut. Our Honing Rod Guide compares the cuts. Learn More
  • F. Dick 12-inch Round Regular Cut Steel with Non-Slip Handle

    Everyday honing on a 12-inch rod lets most knives pass evenly from heel to tip, even long ones, and this round F. Dick steel adds a non-slip handle for a secure grip. It is a dependable steel for butchers, processors and line cooks.The grooves are cut deep and even so they keep working with age, and the handle is sealed to the rod for cleaning in demanding environments. A regular cut restores bite to knives that have started to slide on meat or vegetables. The round profile gives precise control along the curve of a boning or breaking knife.Hang it at the station between uses.A shorter rod is the 10-inch round steel with non-slip handle, and the 14-inch handles scimitars. With a black handle and metal finger guard, the F. Dick 12-inch round butcher steel is a comparable rod. For a smoother edge, step up to the FineCut 12-inch round steel. Learn More
  • F. Dick 14-inch Round Regular Cut Steel with Non-Slip Handle

    Long curved blades such as scimitars and breaking knives need extra length to hone properly, and this 14-inch round F. Dick steel provides it with a secure, non-slip handle. Butchers who hone constantly to keep portions and yields consistent on pork and beef will find it a practical tool.The regular cut straightens edges dulled by bone and joints and restores bite for trimming fat. A sealed handle keeps the steel suitable for the cleanest cutting environments. At this length, the rod lets a 12-inch blade sweep its full edge without running off the tip.A longer rod also keeps the hand farther from the edge as the knife sweeps toward the tip.For knives under 10 inches, the 12-inch round steel with non-slip handle is easier to carry. A black-handled butcher version is the F. Dick 14-inch round butcher steel, and the Dickoron Classic 14-inch round steel adds a sapphire cut. Learn More

Items 51 to 60 of 72 total

per page

Page:
  1. 4
  2. 5
  3. 6
  4. 7
  5. 8