You have no items in your shopping cart.
F. Dick Honing Steels
For the last two hundred years, F. Dick steels have been widely recognized as the best made at world fairs and other competitions. Professional butchers likely have the best understanding of steels, or honing rods. Their work demands they start with a very sharp edge and they hone their knives every ten to fifteen minutes while working. Nearly all butchers use a polished or fine cut steel because they remove a minimum amount of metal from the edge of the knife. They will only realign the existing edge, which is what a steel is designed to do.
Our recommendation is to work with a very fine stone to rebuild your edge and a fine-cut F. Dick steel to keep it straight. When you are working as a carver / butcher, honing your knife four to six times an hour, for a full shift, you will probably want to use a Friedrich Dick polished steel in order to avoid wearing the edge down. Most cooks hone the knife before starting work or after taking it to the sharpening stone. For them, the F. Dick regular cut steel works well. If you keep the knife edge aligned, you won’t have to grind a new edge as often and the knife lasts longer.
-
F. Dick Dickoron Titan 12-inch Oval Coated Steel
Harder knives need a harder steel, and the Dickoron Titan is made for them. Its ultra-hard special coating is three times harder than standard sharpening steels, so it can work knives above 60 Rockwell that a standard rod would barely touch.The coating is slightly more abrasive than other steels, which helps it bring back an edge on hard Japanese knives and Damascus blades evenly. Meat processors also use it for the edge it gives for cutting through beef. For a fine finish, F. Dick recommends following it with the Dickoron Classic, and the oval face keeps the angle steady.For a cook with a mixed roll of German and Japanese knives, it handles the hardest blades in the set.Pair it with the Dickoron Classic 12-inch oval steel for that finishing step. Another rod for hard steels is the F. Dick DarkNitro 12-inch oval steel. A diamond option is the Dickoron Duo diamond and ceramic steel. Learn More$133.25 -
F. Dick Dickoron Micro 12-inch Oval Super Fine Cut Steel
Among serious professionals, this is the F. Dick steel we sell most. If your work is breaking down whole carcasses or cutting steak portions all day, you want the finest edge a steel can give, and the Dickoron Micro’s super fine cut delivers it. F. Dick cuts the lines evenly and to the right depth, and the rod’s hard surface wears very slowly.The oval profile makes honing more forgiving, because the flatter face gives the blade a steady surface to ride on and more contact per stroke. The handle is sealed to meat industry hygiene standards, so it holds up to the cleaning a processing room demands.
Other Dickoron SteelsThe F. Dick Dickoron 12-inch Oval Polishing Steel is the smooth version for the softest knives and the final polish. For an everyday steel at a lower cost, our best-selling steel overall is the F. Dick EuroCut 12-inch Round Regular Cut Steel. Learn More$112.45 -
F. Dick Dickoron Polish 12-inch Oval Polished Steel
For extreme sharpness on knives with a very slim edge angle, F. Dick makes the Dickoron Polish. Its highly polished surface straightens the edge and polishes it without wearing the knife, which suits repetitive use through a long day.Meat processors, butchers and sushi chefs choose a polished steel over a coarser one when they want the smoothest possible edge. The Polish can follow a coarser steel to refine an edge the fine cut has roughened. The substantial Dickoron handle balances the 12-inch oval rod.A few light strokes before each service keep a thin edge standing upright, and the knife needs the stones less frequently.For a little more correction, the Dickoron Micro 12-inch Oval Super Fine Cut Steel adds an ultra-fine cut. A square rod with both sapphire and polished faces is the Dickoron Combi 12-inch square steel. A smaller polished rod with a non-slip handle is the Poliron 10-inch oval steel. Learn More$108.55 -
F. Dick Honorary 12-inch Oval Sapphire Cut Steel
The Honorary steel is the top of F. Dick’s range, a 12-inch oval rod with a handle that can be engraved. It makes a presentation piece for a retiring butcher, a culinary graduate or a chef marking a milestone.The rod carries the same fine sapphire cut as the Dickoron steels, so it hones gently and leaves a fine, even edge. It is extra hardened for less wear, and with the right care it can last a lifetime. The balance between the wood handle and the oval rod makes it comfortable for the long, steady strokes of daily honing.It is a steel to hand down to the next generation.The same sapphire cut with a plastic handle is the Dickoron Classic 12-inch oval steel. For a wood-handled steel to match a knife set, see the F. Dick DarkNitro steel with its oak handle or the F. Dick 1905 10-inch steel. Learn More$136.50 -
F. Dick Dickoron Classic 12-inch Oval Sapphire Cut Steel
In Germany, the Dickoron oval is one of the steels professionals prefer, and it gives an extremely sharp edge. This 12-inch Dickoron Classic combines the sapphire cut with an oval rod that makes the angle easy to hold.What separates the sapphire and fine cuts? Both are grooved to a similar depth, but the sapphire has straight, very fine striations running from handle to tip, while the fine cut runs in a wavy S pattern. The fine cut is therefore slightly more aggressive in texture than the sapphire. The oval face spreads the stroke across more of the edge for quick, even results.It suits sushi and fish work as well as butchery.A round version is the Dickoron Classic 12-inch round steel. For an ultra-fine finish, serious professionals choose the Dickoron Micro 12-inch Oval Super Fine Cut Steel. The S-pattern fine cut is available on the FineCut 12-inch oval steel. Learn More$119.60 -
F. Dick 12-inch Oval Regular Cut Butcher Steel
An oval face makes it easier to find and hold the honing angle, and this 12-inch F. Dick butcher steel pairs that shape with a regular cut and a metal finger guard. It suits cooks who want a more forgiving rod than a round steel.The regular cut grooves leave the edge with a little bite, which helps when slicing tomatoes and other vegetables thinly, and the edge also cuts proteins well. A couple of strokes on each side are enough to bring back a knife that has started to slide. The guard adds balance, and the hang ring keeps the steel at hand.The oval shape is also easier to learn on.A round version is the 12-inch round butcher steel. For a lighter oval rod, the EuroCut 12-inch oval regular cut steel is another choice. A smoother finish comes from an oval fine cut such as the EuroCut 12-inch oval fine cut steel. Learn More$66.30 -
F. Dick 10-inch Oval Diamond Sharpening Steel with Non-Slip Handle
When a regular steel no longer brings an edge back, a diamond rod will, without soaking a stone or learning to hold an angle on one. Diamond is the fastest-cutting rod there is. This F. Dick rod is 600 grit with a solid core, and that construction matters. Diamond pressed into a solid core lasts for years, while hollow rods with an epoxied coating can wear through in six months to a year of regular use.The oval profile puts more of the rod against the blade on each stroke, so it takes fewer strokes, and you can feel the bevel against the rod more clearly. Diamond also works on hard steels that a plain steel rod cannot touch. Its one drawback is a slightly rougher finish, so it is worth following with a few strokes on a ceramic rod such as the Idahone 12-inch Fine Ceramic Sharpening Rod, Black Wood Handle.
Diamond or Steel?For daily upkeep on a knife that is still sharp, a cut steel such as the F. Dick 10-inch Round Fine Cut Sharpening Steel, Red Handle is gentler and removes less metal. Keep the diamond rod for edges that have gone dull. Our Honing Rod Guide covers when each one makes sense. Learn More$66.30 -
F. Dick FineCut 12-inch Oval Steel with Non-Slip Handle
The FineCut surface looks different from most steels, with grooves shaped like a run of S curves rather than straight lines. It removes a burr and smooths the edge without leaving micro-serrations, so it is recommended for Japanese knives as well as German ones.At 12 inches, the rod gives long slicers and 10-inch chef’s knives a full stroke from heel to tip. The oval profile presents a wide face that makes the angle easier to hold. A rod that actually straightens the edge and holds up under heavy use is what keeps a busy kitchen cutting cleanly between sharpenings.For a cook with both German and Japanese knives, one fine cut rod can look after the whole roll.A shorter version is the FineCut 10-inch oval steel, and a round profile is the FineCut 12-inch round steel. For more bite, the 12-inch oval regular cut steel with non-slip handle has the same shape. Learn More$74.10 -
F. Dick FineCut 10-inch Oval Steel with Non-Slip Handle
Rather than straight grooves, the FineCut pattern resembles a series of S shapes. It removes a burr and smooths the edge without leaving micro-serrations, and it works well on German knives and on Japanese knives too.A 10-inch rod is short enough to carry in a scabbard and long enough for most kitchen knives, including chef’s knives and breaking knives up to 10 inches. The oval face gives more contact than a round rod, so the edge comes back in fewer strokes. Because it is a fine cut, it maintains an edge rather than repairing a damaged one.It also suits a scabbard on the belt.A 12-inch version is the FineCut 12-inch oval steel. When the edge needs more correction, a regular cut such as the 10-inch round steel with non-slip handle takes it further. A red-handled round fine cut is the F. Dick 10-inch round fine cut steel. Learn More$73.45 -
F. Dick Poliron 10-inch Oval Polished Steel with Non-Slip Handle
Butchers and meat processors who want the smoothest edge a honing rod can give reach for a polished steel such as the Poliron. A smooth edge cuts meat without tearing, which helps keep portions even and yields high.A polished surface removes no metal. It straightens the edge and polishes it, so it can follow a coarser steel to refine an edge that a regular or fine cut has roughened. Slim edges tend to fold over before they actually go dull, and a few strokes on the Poliron set them upright again. The oval face makes the angle easy to hold.To pair it with a coarser rod, the 10-inch round regular cut steel with non-slip handle shares the handle style. A square rod with polished and fine faces is the F. Dick 10-inch square polished and fine cut steel, and a Dickoron polished rod is the Dickoron Polish 12-inch oval steel. Learn More$79.30
